Skip to main content

hobbyFoam

Search This Blog

CFD Simulations

Get link
Facebook
X
Pinterest
Email
Other Apps

CFD Simulations

CFD of Perrinn F1

Perrinn F1 - Halo
Perrinn F1 - Side Pod Vane Part 1
Perrinn F1 - Side Pod Vane Part 2

Designing and STL Repairing

Designing noses for Perrinn F1
Creating Solid Model of Perrinn F1 for CFD Simulations
STL Repairing
Modifying of STP File of Perinn myP1

CFD Simulations

Validations of the custom codes

Simulation of Ahmed Body by compressible negative Spalart Allmaras model
Simulation of Ahmed Body by compressible solver with Spalart Allmaras model
Ahmed Body DES steady simulation by Local Time-Stepping Pimple solver (SA-RC DDES)
Comparison of Rotation/Curvature Corrections with the original Spalart Allmaras model
Ahmed Body by Local Time-Stepping Pimple solver
(Setup for SIMPLE / Setup for LTS PIMPLE / Results)

RANS Simulations

Perrinn myP1 wind tunnel simulation

Perrinn myP1

Comparison of OF-2.3.0 and foam-extend-3.2 (rhoSimpleFoam)
Ahmed Body
(Meshing / Setup / Result)
PUYO (Honda's concept car)
(Meshing / Setup / Result)
car
(Meshing / Setup / Result)

LES Simulations

Formula car nose
(Meshing / Setup / Result / Animations)

Meshing Tools

foamyHexMesh

Perrinn myP1
Simple Shapes

snappyHexMesh

Comparison of OF-2.3.0 and foam-extend-3.2

Misc.

Mt. Fuji
System preparation for foam-extend-3.2 (OpenSUSE 13.2)

Get link
Facebook
X
Pinterest
Email
Other Apps

Comments

Post a Comment

Pages

Home
CFD Simulations
CFD Software
My CAD files on Onshape
About me

Contact

Linkedin
send an email to me

Links for Perrinn Project

Perrinn.com
Perrinn F1 Onshape
Perrinn F1 2016 Onshape
Perrinn LMP1 Onshape

My GitHub

hf-foam-4.0 repository
Negative Spalart Allmaras Model
incompressible SST-V turbulence model
VONOS div scheme
Wall Function of Turbulence Viscosity Derived from SA model

Popular Posts

SIMPLEC Algorithm of OpenFOAM

1. SIMPLE Algorithm Governing equations can be written as follows using Rhie-Chow interpolation. In OpenFOAM, Eq.(1-2) are written as follows. Step.1: Solve Eqn.(1') implicitly by p* = p0 (p of previous time) and obtain U* Step.2: From continuity equation (div(U) = 0) and Eqn.(3-4), Eqn.(5) can be obtained. Here, an approximation (Eqn.(6)) was used. Step.3: Solve Eqn.(5) implicitly and obtain p. Step.4: Correct U using Eqn.(1'-2'), Eqn.(3-4) and Eqn.(6). Step.5: Go to next time and repeat from Step.1 if not converged. 2. SIMPLEC Algorithm In SIMPLEC Algorithm, the following approximation is used instead of Eqn.(6). In OpenFOAM's expression, Here we can obtain Eqn.(8) from Eqn.(2''). Step.1: Same as SIMPLE Algorithm. Step.2: From continuity equation (div(U) = 0), Eqn.(3-4) and Eqn.(8), Eqn.(5') can be obtained. Step.3: Solve Eqn.(5') implicitly and obtain p. Step.4: Correct U using Eqn.(1'), ...

CFD for Halo of Formula 1

1. Overview I was curious about what halo does in aerodynamics of an F1 car. In this article, I will show the results of CFD simulations of an F1 car, one is without a halo, and the other is with a halo. 2. Halo The halo was desigined using the following document. https://www.fia.com/sites/default/files/fia_standard_8869-2018_afp_v1_0.pdf Perrinn F1 V13 was used as the car, which was designed according to the 2017 F1 technical regulations. 3. Simulation Setup Wind Speed: 50 m/s Ride Height: 20mm/50mm (Front/Rear) Solver: foam-extend-3.2 steady-state solver Turbulence Model: Spalart Allmaras (+Rotation/Curvature Correction) 4. Forces SCd = Frontal Area × Drag Coefficient SCl = Frontal Area × Lift Coefficient L/D = SCl / SCd FrDF% = Front Downforce / Downforce SCl_F = Frontal Area × Front Lift Coefficient SCl_R = Frontal Area × Rear Lift Coefficient Mass = Mass Flow Rate Passing Through Rad...

Meshing with foamyHexMesh

foamyHexMesh is a new mesh generator added in OpenFOAM 2.3.0. In this post, I tried foamyHexMesh for simple shapes (a box and a sphere). Thinking of foamyHexMesh as a meshing tool for air-flow simulations about a car, I created the box as the computational domain which has inlet and outlet, and the sphere as a substitute of a car. Box Sphere I exported these shapes as STL files. Box.stl is separated into 4 parts (inlet, outlet, side, and ground). The diagonal points of the box is (-1, -1, 0) and (1, 1, 1). And the center of the sphere is (0, 0, 0) and the radius of the sphere is 0.5. Box.stl Sphere.stl Here are the steps of using foamyHexMesh. 1. Modify orientations of the faces of STL files at first $ surfaceOrient constant/triSurface/Sphere.stl -inside '(-0.9 0 0.1)' constant/triSurface/Sphere.stl $ surfaceOrient constant/triSurface/Box.stl -inside '(-0.9 0 0.1)' constant/triSurface/Box.stl 2. Create intersections of th...

Powered by Blogger